|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
High-speed Buffer Amplifier for CCD Image Sensor CXA3791EN Description The CXA3791EN is a high-speed buffer amplifier IC. (Applications: CCD image sensor output buffers, Digital still cameras, Camcorders, Other general buffers) Features Power consumption: 22mW (typ.) (IDRV = 50A (180k when VCC = 13V), ISF pin connected to GND, during no signal) Push-pull output High-speed response: 500V/s (IDRV = 50A (180k when VCC = 13V), CL = 20pF) Internal sink current mode for CCD with open source output (Settable by external resistance RISF) Enables to set the responsibility by changing the drive current by an external resistor Structure Bipolar silicon monolithic IC Absolute Maximum Ratings (Ta = 25C) Supply voltage Supply voltage Storage temperature Allowable power dissipation VCC IN Tstg PD 16 GND - 0.3 to VCC + 0.3 -65 to +150 0.22 V V C W (when mounted on a two-layer board; 13mm x 13mm, t = 0.63mm) Recommended Operating Conditions Supply voltage Operating temperature VCC Ta 9.0 to 15.5 -20 to +75 V C Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. -1- E08233-PS CXA3791EN Block Diagram and Pin Configuration (Top View) ISF 6 VCC 5 IDRV 4 1 IN 2 GND 3 OUT Pin Description and I/O Pin Equivalent Circuit Pin No. 2 5 Symbol GND VCC I/O -- -- Standard voltage level 0V 13V Equivalent circuit -- -- VCC 2k 10 x IDRV Description GND. Supply voltage input. 1 IN I CCD output voltage 1 Input. 58 x IISF 10 x IDRV 2k GND VCC 6 ISF I -- 6 30k 20k GND External resistor connection for setting the sink current for CCD with open source output. Connect an external resistor between this pin and VCC (Pin 5). Connect this pin to GND (Pin 2) when not using this function. * Set the resistance so that ISF current is 90A or less. VCC 50 3 OUT O IN 50 3 Output. GND VCC 4 IDRV I -- 4 30k 20k GND External resistor connection for setting the drive current. Connect an external resistor between this pin and VCC (Pin5). * Set the resistance so that IDRV current is 90A or less. -2- CXA3791EN Electrical Characteristics (Ta = 25C, VCC = 13V, RIDRV = 180k, ISF pin: connected to GND) DC Characteristics Item Supply current Voltage gain I/O offset voltage Symbol ICC VGAIN VOFFSET Measurement conditions IN = 10V, RIDRV = 180k *1 Min. 1.4 -- -100 3.3 2.9 2.5 2.1 -15 2.6 Typ. 1.6 0.999 -- -- -- -- -- -5 2.9 Max. 1.8 -- 100 VCC - 2.0 VCC - 1.85 VCC - 1.8 VCC - 1.7 6 3.2 Unit mA V/V mV IN: 10Vdc V = 1V GAIN = OUT/V IN = 10V VOFFSET = OUT-IN RIDRV = 78k RIDRV = 120k RIDRV = 180k RIDRV = 270k IN = 10V, ISF = 0V IN = 10V, RISF = 180k I/O voltage range Input bias current Sync current *1 VRANGE IBIAS ISINK V A mA Voltage gain 10.5V IN V = 1V 9.5V OUT OUT -3- CXA3791EN AC Characteristics (Ta = 25C, VCC = 13V, IDRV = 50A (180k when VCC = 13V), ISF pin: connected to GND, RL = 15, CL = 20pF) Item Bandwidth Rise time Symbol GBW TRISE Measurement conditions IN = 50mVp-p *1 Min. -- -- Typ. 220 2.5 Max. -- 3.5 Unit MHz ns IN = 9.5 to 10.5V 10 to 90% *1 Fall time TFALL IN = 10.5 to 9.5V 10 to 90% *1 -- 3.0 4.0 ns I/O delay time TDELAY IN = 9.5 to 10.5V @50% 0.9 1.0 2.0 ns *1 Rise time, fall time and I/O delay time 10.5V 50% 9.5V IN 90% OUT 10% 10% 90% 50% TFALL TRISE TDELAY -4- CXA3791EN Evaluation Circuit 180k 1000pF ISF 6 VCC 5 47F IDRV 4 180k 1 IN 2 GND 15 20pF 3 OUT A 13V GND -5- CXA3791EN Description of Operation Current Settings 1. Output Drive Current The small signal output impedance of the OUT pin (Pin 3) can be set by connecting the IDRV pin (Pin 4) to VCC through a resistor. The inflow current to the IDRV pin is multiplied by 10 times inside the IC, and flows as the output stage idling current. The IDRV pin has an internal 50k resistor, so the inflow current to the IDRV pin can be calculated as follows. IIDRV = (VCC - VBE x 2)/(RIDRV + 50k) = (13 - 1.46)/(180k + 50k) = 50.2A Here, VCC = 13V, VBE = 0.73V (typ.), and RIDRV = 180k. The small signal output impedance at this time can be calculated as follows. ROUT = (26mV/(10 x IIDRV))/2 = (26mV/502A)/2 = 26 2. Sink Current for CCD with open source output The sink current of the IN pin (Pin 6) can be set by connecting the ISF pin (Pin 1) to VCC through a resistor. This sink current can be used as the CCD output stage source follower drive current. The inflow current to the ISF pin is multiplied by 58 times inside the IC, and flows as the sink current. The ISF pin has an internal 50k resistor, so the inflow current to the ISF pin can be calculated as follows. IISF = (VCC - VBE x 2)/(RISF + 50k) = (13 - 1.46)/(180k + 50k) = 50.2A Here, VCC = 13V, VBE = 0.73V (typ.), and RISF = 180k. The sink current at this time can be calculated as follows. Isink = 58 x IISF = 2.9mA Note) This IC operation depends on IDRV and ISF. Set the external resistance so that IDRV and ISF current are 90A or less, referring to the table shown below. [IDRV and ISF vs. external resistor] Current (A) When VCC = 15V When VCC = 13V 90 100 78 68 150 120 50 220 180 35 330 270 26 470 390 Unit k k -6- CXA3791EN Example of Representative Characteristics (Upper side) I/O voltage range vs. IDRV pin setting resistance Vcc - 0.0 Ta = 25C 0.5 1.0 3.5 5.0 Ta = 25C 4.5 4.0 (Lower side) I/O voltage range vs. IDRV pin setting resistance I/O voltage [V] 1.5 2.0 2.5 3.0 I/O voltage [V] Vcc = 13V Vcc = 15V 3.0 2.5 2.0 1.5 1.0 Vcc = 15V Vcc = 13V 3.5 4.0 0 50 100 150 200 250 300 350 IDRV pin setting resistance [k] 0.5 0.0 0 50 100 150 200 250 300 350 IDRV pin setting resistance [k] Current consumption vs. IDRV pin setting resistance 4.0 Ta = 25C 3.5 Sink current vs. ISF pin setting resistance 7.0 Ta = 25C 6.0 5.0 4.0 3.0 2.0 1.0 0.0 Current consumption [mA] 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0 50 100 150 200 250 300 350 IDRV pin setting resistance [k] Vcc = 13V Vin = Vcc - 4V Vcc = 15V Vin = Vcc - 5V Sink current [mA] Vcc = 15V Vin = Vcc - 5V Vcc = 13V Vin = Vcc - 4V 0 50 100 150 200 250 300 350 ISF pin setting resistance [k] Current consumption vs. Supply voltage 2.0 Ta = 25C 1.8 Ridrv = 180k Vin = Vcc - 4V Current consumption vs. Operating temperature 2.0 Current consumption [mA] Current consumption [mA] 1.8 Vcc = 15V Ridrv = 220k Vin = Vcc - 5V Vcc = 13V Ridrv = 180k Vin = Vcc - 4V 1.4 1.6 1.6 1.4 Ridrv = 220k Vin = Vcc - 5V 1.2 1.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 1.2 -50.0 -25.0 0.0 25.0 50.0 75.0 100.0 Supply voltage [V] Operating temperature [C] -7- CXA3791EN I/O offset voltage vs. Supply voltage 20.0 Ta = 25C I/O offset voltage vs. Operating temperature 20.0 10.0 I/O offset voltage [mV] I/O offset voltage [mV] 10.0 0.0 Ridrv = 220k Vin = Vcc - 5V -10.0 Ridrv = 180k Vin = Vcc - 4V 0.0 Vcc = 13V Ridrv = 180k Vin = Vcc - 4V Vcc = 15V Ridrv = 220k Vin = Vcc - 5V -10.0 -20.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 -20.0 -50.0 -25.0 0.0 25.0 50.0 75.0 100.0 Supply voltage [V] Operating temperature [C] Input bias current vs. Supply voltage 5.0 Ta = 25C Input bias current vs. Operating temperature 3.4 3.2 Input bias current [A] Input bias current [A] 0.0 Ridrv = 220k Vin = Vcc - 5V -5.0 Ridrv = 180k Vin = Vcc - 4V -10.0 3.0 Vcc = 15V Ridrv = 220k Vin = Vcc - 5V Vcc = 13V Ridrv = 180k Vin = Vcc - 4V 2.8 2.6 -15.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 2.4 -50.0 -25.0 0.0 25.0 50.0 75.0 100.0 Supply voltage [V] Operating temperature [C] Sink current vs. Supply voltage 4.0 Ta = 25C 3.5 Sink current [mA] Sink current [mA] Sink current vs. Operating temperature 3.4 3.2 Ridrv/Risf = 180k Vin = Vcc - 4V 3.0 3.0 Vcc = 15V Ridrv/Risf = 220k Vin = Vcc - 5V Vcc = 13V Ridrv/Risf = 180k Vin = Vcc - 4V 2.5 Ridrv/Risf = 220k Vin = Vcc - 5V 2.0 2.8 2.6 1.5 10.0 11.0 12.0 13.0 14.0 15.0 16.0 2.4 -50.0 -25.0 0.0 25.0 50.0 75.0 100.0 Supply voltage [V] Operating temperature [C] -8- CXA3791EN Tr and Tf vs. Supply voltage 6.0 4.0 3.5 3.0 4.0 Tr and Tf [ns] Tr 3.0 Tr and Tf [ns] Tf 2.5 2.0 1.5 1.0 0.5 Tr and Tf vs. Operating temperature 5.0 Tf Tr 2.0 Ta = 25C, Idrv = 50A, CL = 20pF, RL = 15, Input DC offset = VCC - 5V, Input amplitude = 1.0V, Input rise, fall time = 2.0ns 11.0 12.0 13.0 14.0 15.0 16.0 1.0 Idrv = 50A, CL = 20pF, RL = 15, Input DC offset = VCC - 5V, Input amplitude = 1.0V, Input rise, fall time = 2.0ns -25 0 25 50 75 100 0 10.0 0 -50 Supply voltage [V] Operating temperature [C] I/O delay time vs. Supply voltage 2.00 1.75 1.50 I/O delay time [ns] 1.25 1.00 0.75 0.50 0.25 0 10.0 Ta = 25C, Idrv = 50A, CL = 20pF, RL = 15, Input DC offset = VCC - 5V, Input amplitude = 1.0V, Input rise, fall time = 2.0ns 11.0 12.0 13.0 14.0 15.0 16.0 I/O delay time [ns] I/O delay time vs. Operating temperature 2.00 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0 -50 Idrv = 50A, CL = 20pF, RL = 15, Input DC offset = VCC - 5V, Input amplitude = 1.0V, Input rise, fall time = 2.0ns -25 0 25 50 75 100 Supply voltage [V] Operating temperature [C] Positive pulse response 0.2V/div 0.2V/div Negative pulse response Idrv = 50A, CL = 20pF, RL = 15 Input rise, fall time = 2.0ns T Input T 10.0V T Output 10.0V Output T Input Idrv = 50A, CL = 20pF, RL = 15 Input rise, fall time = 2.0ns Ch1 200mV Ch2 200mV M 1.00ns Ch1 10.0V Ch1 200mV Ch2 200mV M 1.00ns Ch1 10.0V 1.0ns/div 1.0ns/div -9- CXA3791EN Application Circuit 1 when using CCD with open source output 180k 1000pF 0.1F ISF 6 VCC 5 IDRV 4 0.1F 180k 1 IN 2 GND 3 OUT 13V GND CCD CDS/ADC Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same. - 10 - CXA3791EN Application Circuit 2 when using CCD with internal current source 180k 1000pF ISF 6 VCC 5 0.1F IDRV 4 1 IN 2 GND 3 OUT 13V GND CCD CDS/ADC Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same. - 11 - CXA3791EN Notes on Operation Provide the widest GND pattern possible on the board. Use a 1000pF (recommended) and a 0.1F (recommended) ceramic capacitors in parallel for the bypass capacitor connected between the power supply and GND, and connect them as close to the IC pins as possible. Load capacitance causes the input/output wiring response to worsen and results in noise. Use the shortest wiring layout possible, and shield it with GND. When the output pin (Pin 3) is shorted to either the power supply or GND, an overcurrent may flow to the output stage elements and damage them. When the input pin (Pin 1) is shorted to GND, an overcurrent may flow to the internal parasitic elements and damage them. - 12 - CXA3791EN Package Outline (Unit: mm) LEAD PLATING SPECIFICATIONS ITEM LEAD MATERIAL SOLDER COMPOSITION PLATING THICKNESS SPEC. COPPER ALLOY Sn-Bi Bi:1-4wt% 5-18m - 13 - Sony Corporation |
Price & Availability of CXA3791EN |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |